Máy khách hàng tại Hoocmon bị lỗi trục Z không di chuyển được, hư bộ điều khiển drive các trục, chúng tôi đến kiểm tra cài đặt và sửa chữa bàn giao xong cho khách hàng trong 1 buổi.
Chúng tôi chuyên sửa chữa máy phay CNC Mazak VQC-20/50B đời 1985 hệ điều khiển Mazatrol cam M2 các lỗi như lỗi servo alarm, lỗi giao tiếp không truyền được chương trình gia công Với đội ngũ kỹ sư điện tử chuyên sâu chuyên sửa chữa các bộ phần như Servo Amplifier, Servo các trục, DC Driver, Spindle Amplifier Module, máy tính công nghiệp
CÁC LỖI VỀ MÁY MAZAK:
2 EMERGENCY STOP
Cause
Trouble has occurred in the hardware.
Action
Turn power off and then back on. If this does not clear the alarm status, require Mazak Technical Center or Technology Center to replace the defective hardware or cables.
3 EMERGENCY STOP
Cause
The emergency stop button on the operating panel has been pressed.
Action
Release the pressed state of the emergency stop button and reset the NC unit to its initial state.
5 SYSTEM SOFTWARE ERROR
Cause
The contents of the system software and/or custom software have been destroyed.
Action
Contact Mazak Technical Center or Technology Center.
6 REMOTE I/O ERROR
Cause ——
Action
Contact Mazak Technical Center or Technology Center.
7 SRAM MALFUNCTION
Cause
The S-RAM mounted on the CPU card has become abnormal.
Action
Contact Mazak Technical Center or Technology Center.
8 RAM MALFUNCTION
Cause
The RAM mounted on the CPU card has become abnormal.
Action
Contact Mazak Technical Center or Technology Center.
9 ABSOLUTE POSITION MALFUNCTION
Cause
The absolute position detection system has lost absolute position data.
Action
Require Mazak Technical Center or Technology Center to re-set the absolute position data.
10 DETECTOR MALFUNCTION
Cause
The absolute position detection system has detected its detector error(s).
Action
Require Mazak Technical Center or Technology Center to replace the encoder or bettery.
11 POSITION REFERENCE MALFUNCTION
Cause
The absolute position detection system has detected an error(s) by cross-checking the absolute position of its detector and the internal coordinate data of the NC unit.
Action
Require Mazak Technical Center or Technology Center to re-set the absolute position data.
12 ABSOLUTE POSITION WARNING
Cause
The absolute position detection system has detected abnormal data.
Action
The battery is running down. Require Mazak Technical Center or Technology Center to replace the battery.
13 PRE-PROCESSOR MALFUNCTION
Cause
The software is not correctly working.
Action
Require Mazak Technical Center or Technology Center to re-write the NC system data.
21 SYSTEM ERROR
Cause
Trouble has occurred during communication with the amplifiers or during communication data processing.
Action
Contact Mazak Technical Center or Technology Center with the information of the numbers (Alarm No. and Sub No.) displayed in parentheses.
22 AMPLIFIER NOT EQUIPPED
Cause
Amplifier power is not yet turned on. Or no signals are transferred yet. There is a discrepancy between the channel and rotary switch Nos. of the amplifier and the parameters concerned.
Action
Check for an incorrectly connected cable, an incorrectly attached connector, an inadequate input supply voltage to the amplifier, an incorrect axis-number switch setting, etc. Check the settings of parameters N17, N18, SA43, and SA44 for incorrectness.
26 SPINDLE SAFE OPER. SYSTEM ALARM
Cause
Trouble has occurred for the spindle in the mode of safety-speed operation. See the description of No. 25 above for the details of probable causes.
Action
Contact Mazak Technical Center or Technology Center with the information of the first item (Alarm No.) displayed in parentheses.
31 SERVO MALFUNCTION 1
Cause
The servo (power-off level) is abnormal.
Action
Require Mazak Technical Center or Technology Center to replace the servo amplifier.
32 SERVO PARAMETER MALFUNCTION
Cause
The parameters that have been transferred from the NC unit to the servo amplifier during NC power-on are not correct. Action Require Mazak Technical Center or Technology Center to re-set the servo parameters.
33 SERVO MALFUNCTION 2
Cause
The servo (NC reset level) is abnormal.
Action
Contact Mazak Technical Center or Technology Center with the information of the first item (Alarm No.) displayed in parentheses.
34 SERVO MALFUNCTION 3
Cause
The servo (amplifier power-off level) is abnormal.
Action
Contact Mazak Technical Center or Technology Center.
35 OVERLOAD
Cause
An extraordinary overload has been detected.
Action
Check if any collision has occurred on the machine and perform the corresponding recovery, or check and reduce the cutting conditions. If other measures other than the above should be taken, contact Mazak Technical Center or Technology Center with the information of the first item (Alarm No.) displayed in parentheses.
41 SPINDLE MALFUNCTION 1
Cause
The spindle (power-off level) is abnormal.
Action
Contact Mazak Technical Center or Technology Center with the information of the first item (Alarm No.) displayed in parentheses.
42 SPINDLE PARAMETER MALFUNCTION
Cause
The parameters that have been transferred from the NC unit to the spindle amplifier during NC power-on are not correct.
Action
Require Mazak Technical Center or Technology Center to re-set the spindle parameters.
43 SPINDLE MALFUNCTION 2
Cause
The spindle (NC reset level) is abnormal.
Action
Contact Mazak Technical Center or Technology Center with the information of the first item (Alarm No.) displayed in parentheses.
44 SPINDLE MALFUNCTION 3
Cause
Công ty TNHH NAMFARE
MST: 3703122568
Hotline/ Zalo: 0937029193
Email: namfaregroup@gmail.com
Địa chỉ: Thửa đất số 883, tờ bản đồ số 04, đường ĐT741, Khu Phố An Lợi, Phường Hòa Lợi, Thị Xã Bến Cát, Tỉnh Bình Dương, Việt nam
TK: Ngân Hàng ACB, công ty TNHH NAM FARE, STK: 6868976
